The best jigsaw blades for metal are bi‑metal, fine‑tooth T‑shank blades with 18–32 TPI.
You know the feeling. You mark a clean line on sheet steel or a stubborn bolt, then your blade chatters, heats up, and quits. I’ve been there. The wrong blade wastes time and burns money. The right one glides, stays cool, and saves the workpiece. In this guide, I break down the best jigsaw blades for metal for clean, fast, low-burr cuts. I’ll show you where each blade shines, how to match TPI to thickness, and what to buy if you cut thin sheet, thick bar, or mixed materials. I’ll keep it simple, factual, and based on shop use.
50 Piece Contractor Jigsaw Blades…
No description found
Jigsaw Blades, 10 Piece Jig…
Value Package: Each set comes with 10 Piece jigsaw blades of different models for a wide range of uses. T118A,T118B for basic metal; T101AO,T101D,T101B,T101BR for clean wood, T144D,T244D,T111d for speed…
DEWALT – DW3770-5 Jigsaw Blades,…
Unique curved tooth design of the jigsaw blades minimizes stress points for longer blade life and faster cuts Cobalt steel (Bi-Metal) of the jig saw blade maximizes blade life and…
50-Pc Contractor T‑Shank Jigsaw Blade Set + Case
This 50-piece contractor set gives you a deep bench of T‑shank blades across common profiles. You get staples like T118A and T118B for sheet metal and thin stock, plus wood-focused T101 and T144D for fast cuts in lumber. The mix suits jobsite work where you switch from conduit to plywood and back. The storage case keeps sizes sorted so you can grab the right tooth count fast.
For metal, the standout SKUs here are T118A (fine, for thin sheet) and T118B (slightly coarser, for light-gauge to medium stock). These are usually high-speed steel or bi‑metal, which handle heat better than plain carbon steel. I run them slow with light oil to reduce burrs. If you cut only metal all day, there are more specialized packs, but for mixed tasks this kit brings real value.
Pros:
- Huge value with 50 blades and a sturdy case
- Includes T118A and T118B for thin to medium metal
- Reliable T‑shank fit for most modern jigsaws
- Good mix for jobsite users who cut both metal and wood
- Easy to restock common codes when you learn your favorites
Cons:
- Not a dedicated metal-only kit
- Blade steel and edge life vary across profiles
- Fewer high-TPI options for ultra-thin stainless
My Recommendation
This set suits contractors, DIYers, and maintenance techs who switch materials often. If you need the best jigsaw blades for metal and wood in one box, this is a smart first buy. For frequent sheet-metal work, keep a dedicated fine-TPI pack on hand and use this as your backup and wood option. Stock is common, and pricing is fair for the count.
| Best for | Why |
| Mixed-material projects | Includes both metal and wood SKUs in one case |
| Entry-level buyers | Affordable way to test popular blade types |
| Jobsite spares | High count reduces runs to the store mid-job |
10-Pc Assorted T‑Shank Jigsaw Blades for All Cuts
This 10-pack covers a little of everything, with metal codes T118A and T118B included for thin to light-gauge stock. It’s compact, so it fits in the jigsaw case, yet it gives you several tooth profiles if you need to adapt mid-task. For new users, it’s a good sampler that helps you feel the difference between fine and coarse teeth in both metal and wood.
For best results on metal, use slower strokes, minimal orbital action, and support thin sheet with a backer. I like the T118A here for HVAC tin, aluminum trim, and thin stainless. The T118B handles a bit thicker material but still prefers sheet. If your work leans heavy on steel, grab a thicker-metal specialty pack too.
Pros:
- Compact assortment fits in your saw case
- Includes T118A and T118B for thin sheet metals
- Affordable way to learn TPI selection
- Works with most T‑shank jigsaws
- Balanced set for light metal and wood tasks
Cons:
- Small quantity; you may run out of favorites fast
- Not designed for thick bar or hard alloys
- No ultra-fine 24–32 TPI for delicate stainless
My Recommendation
If you want the best jigsaw blades for metal in a small, low-cost kit, this pack is a smart starter. It’s ideal for light sheet work, quick repairs, and learning curve jobs. Keep it as a backup in your tool bag and add a thick-metal pack as you grow. Good availability and easy to reorder.
| Best for | Why |
| Basic sheet-metal cuts | Fine-tooth T118A/B handles thin stock cleanly |
| Beginners | Clear TPI range teaches blade selection fast |
| Mobile repairs | Lightweight pack fits in small cases |
DEWALT DW3770-5 14 TPI Thick Metal Blades (5)
When you need to cut thicker steel, a 14 TPI blade is the move. This DEWALT pack is built for that job. The teeth are aggressive enough for speed but still tight enough to control chatter. I reach for these on angle iron, pipe, and steel plate where thin-sheet blades would clog and burn.
Run low speed, no orbital, and clamp the work tight. A touch of cutting fluid goes a long way to extend life. If you do HVAC or auto body, these are overkill. But for shop steel and heavier projects, they earn their keep. They’re among the best jigsaw blades for metal when stock gets chunky.
Pros:
- 14 TPI cuts thick steel and angle iron
- Robust body resists heat and flex
- Consistent DEWALT fit and finish
- Good balance of speed and control
- Great value for heavy-duty users
Cons:
- Too coarse for thin sheet or delicate trim
- Requires more feed control to avoid burring
- Five-pack may go fast on daily steel work
My Recommendation
Choose this pack if your work involves angle, bar, or structural steel. It’s the best jigsaw blades for metal when your stock is thick and tough. Pair it with a fine 24–32 TPI set for thin sheet and you’re covered. Always in stock and trusted on job sites.
| Best for | Why |
| Thick steel and angle iron | 14 TPI maintains chip clearance and control |
| Fabrication tasks | Sturdy build handles heat under load |
| Pipe and bar cuts | Tooth form tracks well in curved cuts |
10-Pk T118A 3-In. Basic Metal T‑Shank Blades
The T118A is a workhorse for thin metal. This 10-pack focuses on that one job and does it well. The fine tooth pitch keeps the cut smooth and reduces snags on thin sheet. I like it for HVAC, flashing, and aluminum trim where control matters more than speed.
Set your jigsaw to low speed, turn off orbital, and let the teeth do the work. A backer board on thin sheet helps prevent vibration. If you need to cut thicker steel, move up to T118B or a 14–18 TPI blade. For thin-gauge metals though, these are some of the best jigsaw blades for metal you can buy for the price.
Pros:
- Purpose-built for thin sheet metal
- Clean edges with minimal burrs
- Reliable T‑shank fit
- Great value in a single-task pack
- Easy to standardize consumables in the shop
Cons:
- Not suited for medium or thick steel
- Can cut slowly on harder alloys
- Shorter length limits deep plunge cuts
My Recommendation
If your daily work is thin sheet and trim, buy this pack and keep extras on hand. It is the best jigsaw blades for metal when your priority is clean, controlled cuts in light-gauge stock. Saves time on setup and keeps results consistent. Stock is common and pricing is friendly.
| Best for | Why |
| HVAC sheet metal | Fine pitch prevents snagging and tear-out |
| Aluminum and soft metals | Small gullets reduce chatter and burrs |
| Precise trim cuts | Short length improves control near edges |
Diablo 30 TPI Thin‑Metal Jigsaw Blades (5)
Diablo’s 30 TPI blades are purpose-built for very thin metal. Think stainless sheet, flashing, and tight-radius cuts where you need a silky edge. The bi‑metal body handles heat and flex, while the high tooth count keeps the cut smooth. I like these for stainless backsplashes and appliance trim.
Use low speed and steadied feed. A small amount of cutting wax helps avoid galling on stainless. Compared to T118A, the 30 TPI feels even smoother on ultra-thin stock. For thicker material, switch to 18–24 TPI. If your shop needs fine control, these rank among the best jigsaw blades for metal for delicate work.
Pros:
- Ultra-fine 30 TPI for very thin metals
- Bi‑metal durability resists heat
- Excellent edge quality with low burr
- Great for stainless sheet and trim
- Tracks well on tight curves
Cons:
- Slow in medium or thick steel
- Teeth can clog without lubricant
- Five blades may not last on daily stainless work
My Recommendation
Pick this if you need clean, burr-light cuts in stainless or thin aluminum. It’s the best jigsaw blades for metal when the sheet is delicate and finish matters. Keep it as your finesse option, and pair with a 14–18 TPI set for heavier steel. Supply is steady and the brand is consistent.
| Best for | Why |
| Stainless sheet | 30 TPI lowers burrs and edge work |
| Aluminum trim | Fine teeth reduce grabbing and galling |
| Curved, precise cuts | Blade tracks smoothly on tight paths |
TAROSE T118B 12 TPI Metal Jigsaw Blades (10)
These T118B blades sit in the sweet spot for light-gauge metal. At around 12 TPI, they cut faster than the ultra-fine options and still keep chips in check. I use them on light steel, aluminum angles, and general utility cuts. The 10-pack keeps cost per blade low.
They’re not for thick steel, but they shine when you want a bit more speed on sheet and thin profiles. Use slow speeds and turn off orbital. If you often bounce between thin and very thin materials, pair these with a 21–30 TPI pack. This balance makes them some of the best jigsaw blades for metal in day-to-day shop work.
Pros:
- Faster than ultra-fine TPI on light-gauge stock
- Affordable 10-pack for frequent users
- Stable tracking with reduced chatter
- Good for aluminum and mild steel
- Simple, reliable T118B profile
Cons:
- Not ideal for very thin stainless
- May burr on thicker edges without lube
- Short length limits deep reach
My Recommendation
Choose these if you want a faster cut on light-gauge steel and aluminum with basic cleanup. They rank as the best jigsaw blades for metal when speed matters more than a glassy edge. Stock is easy to find and the value is solid for a 10-pack.
| Best for | Why |
| Light-gauge steel | 12 TPI balances speed and control |
| Aluminum angles | Tooth pace clears chips without heavy burrs |
| General shop cuts | Affordable pack for daily tasks |
TAROSE T118A 21 TPI Metal Jigsaw Blades (10)
The TAROSE T118A at 21 TPI is a great middle ground for thin metals that still need a fine finish. It’s smoother than T118B and faster than 30 TPI. I reach for it when cutting appliance panels, light stainless, and clean edges in aluminum sheet. The 10-pack keeps you covered for a long time.
Use low speed, keep the work braced, and consider a lubricant on stainless. If you need surgical edges, jump to 30 TPI. If you need speed in thicker stock, go down to 14–18 TPI. As a daily driver, these are among the best jigsaw blades for metal for predictable results and low rework.
Pros:
- 21 TPI strikes a clean vs. speed balance
- Handles thin stainless better than coarser blades
- Affordable and consistent
- Good curve control in thin sheet
- Low chatter when fed properly
Cons:
- Not fast on thicker steel
- Can load up on soft aluminum without wax
- Short blade length limits deep reach
My Recommendation
Buy this if you want one go-to blade for most thin metal cuts. It is the best jigsaw blades for metal when you value a clean edge but do not want to crawl. Easy to find and easy to love in daily use.
| Best for | Why |
| Thin stainless panels | 21 TPI reduces burrs with steady feed |
| Aluminum sheet | Good speed with minimal grabbing |
| Everyday thin metal | Balanced performance across materials |
14-Pc U‑Shank Jigsaw Blade Set, Wood/Metal Mix
If your jigsaw takes U‑shank blades, this set keeps you in the game. It includes a range from 6T to 32T, so metal cutters can grab the 18–32 T options for sheet and light stock. The variety helps owners of older saws that lack a T‑shank chuck. It’s a practical way to extend the life of a reliable tool.
For metal, stick to the finer T counts and go slow. Clamp the work, use a little lubricant, and avoid orbital motion. You won’t get as many metal-dedicated options as a T‑shank set, but for a U‑shank saw, this is a handy, budget-friendly kit. It helps you find the best jigsaw blades for metal for your legacy tool.
Pros:
- Supports older U‑shank jigsaws
- Wide tooth range up to 32T for thin metal
- Affordable mixed pack for light tasks
- Convenient for occasional users
- Great backup kit for a second saw
Cons:
- U‑shank can be less secure than T‑shank
- Fewer metal-specialized profiles
- Not ideal for thick steel
My Recommendation
Choose this if you run a U‑shank jigsaw and need a simple metal solution. It is the best jigsaw blades for metal for owners of older tools who cut light-gauge material. Not fancy, but very practical and easy to keep in stock.
| Best for | Why |
| Legacy U‑shank saws | Wide range of tooth counts in one kit |
| Thin sheet metal | Up to 32T options for smooth edges |
| Budget users | Low cost for occasional cutting |
Bosch T5002 10‑Pc T‑Shank Blade Set
The Bosch T5002 is a classic mixed set with dependable quality. For metal, it typically includes T118A/T118B or similar fine-tooth profiles. Bosch’s fit and finish tend to be consistent, so the blades seat well and track straight. I keep this set for backup and for handing to helpers on projects.
For thin steel, use the fine-tooth options and slow speed. For aluminum, a little wax helps reduce loading. The pack is not metal-only, but it performs well and remains easy to source. If you want a solid brand in a small kit, this is among the best jigsaw blades for metal and wood combined.
Pros:
- Trusted brand with consistent sizing
- Includes fine-tooth options for sheet metal
- Good starter kit for mixed materials
- Reliable T‑shank fit for most saws
- Easy to find and reorder
Cons:
- Not a dedicated metal set
- Limited quantity for heavy users
- No ultra-fine 30+ TPI option
My Recommendation
Buy this if you want a trusted brand and a simple, versatile kit. It’s not the most specialized, but it holds its own on metal sheet. For many users, it’s the best jigsaw blades for metal when they also cut wood daily. Widely available, with predictable quality.
| Best for | Why |
| General maintenance | Balanced assortment covers many tasks |
| Occasional metal cuts | Fine-tooth SKUs handle sheet cleanly |
| Brand-loyal buyers | Bosch consistency and fit |
Craluuur 30‑Pc Assorted T‑Shank Blade Set
This 30-piece set packs a big range of profiles, including the key metal codes T118A and T118B. It’s a budget-friendly stock-up option for homeowners and light shop users. The variety means you can dial in cuts on plastic and wood too, which is handy if you flip between tasks.
For metal, lean on the fine-tooth blades and take your time. These sets deliver strong value but may not equal premium lifespan in heavy daily use. Keep a dedicated thick-metal pack for bar and angle steel. As a bulk assortment, it still ranks among the best jigsaw blades for metal when cost per cut matters.
Pros:
- Large assortment at a low price
- Includes T118A/B for thin to light-gauge metal
- Great for mixed-material projects
- Plenty of spares in one purchase
- Good entry point for new users
Cons:
- Inconsistent longevity across profiles
- Not ideal for thick steel
- Assortment may favor wood over metal
My Recommendation
Go for this if you want a big, affordable set to cover many jobs. For thin metal and general use, it’s the best jigsaw blades for metal on a tight budget. Buy a heavy-metal pack later if your projects grow. Stock is flexible and price is right.
| Best for | Why |
| Budget buyers | Lots of blades for low cost |
| Mixed materials | Includes wood, plastic, and metal profiles |
| Light-duty metal | Fine-tooth blades handle sheet steel |
FAQs Of best jigsaw blades for metal
What TPI should I use for metal?
Use 21–32 TPI for thin sheet and 14–18 TPI for thicker steel. Finer teeth make smoother cuts on thin stock.
Are bi‑metal blades better than HSS for metal?
Yes. Bi‑metal blends toughness and heat resistance, so it lasts longer under heat and flex.
Should I use orbital action when cutting metal?
No. Turn orbital off. Use slow speed and steady feed to reduce burrs and heat.
Do I need lubricant when cutting steel?
It helps. A small amount of oil or wax reduces heat, extends blade life, and improves finish.
Can jigsaws cut stainless steel?
Yes. Use fine TPI (21–32), slow speed, no orbital, and lubricant. Clamp the work to reduce vibration.
Final Verdict: Which Should You Buy?
If you want a single thin-metal hero, the Diablo 30 TPI pack is hard to beat. For thick stock, the DEWALT 14 TPI set is the right call.
For mixed tasks, grab the 50-Pc Contractor kit and add a fine pack. You’ll have the best jigsaw blades for metal ready for any job.